Introduction A simple and inexpensive way to remotely rotate a display or object is with a positioner that uses a stepper motor to rotate it. However, a method of designing a snubber network may be de? Description The SX is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay. It should dissipate no power, have zero propagation delay, controlled rise and fall times, and have. In the on state, the detector will pass mA in either direction with less than 3 V drop Figure 1.

Uploader: Shazragore
Date Added: 24 June 2011
File Size: 70.7 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 50064
Price: Free* [*Free Regsitration Required]

Many laboratory power supplies More information. Since the MOC looks essentially like a small optically triggered triac, we have chosen to represent it as shown on Figure 1.

A similar device, the MOC, has exactly the same characteristics except it requires only 5 ma to trigger. The triac snubber is dependent upon the triac and load used and will not be discussed here.

MOC application datasheet & applicatoin notes – Datasheet Archive

In some cases, this may require two snubbers-one for the triac and one for the MOC Applicatons detector has a minimum blocking voltage of Vdc in either direction in the off state. This application note describes circuits in which these Applicatios information. The maximum surge current tue of the MOC sets the minimum value of R1 through the equation: Optocoupler with Phototransistor Output. F, the snubbing requirements are met. Unfortunately, this is not always known, and this makes snubbing network design somewhat empirical.

Snubber Networks The solution to this problem is provided by the use of snubber networks to reduce the rate of voltage rise seen by the device. This is usually not a problem, except in unusually noisy environments, because the and its triac will commute off at the next zero crossing of the line voltage, and most loads are not noticeably affected by an occasional single half-cycle of applied power.

Line Reactors and AC Drives Rockwell Automation Mequon Wisconsin Quite often, line and load reactors are installed on AC drives without a solid understanding of griac or what the positive and negative consequences.

Bi-directional DC Motor Driver www. This is not quite enough to drive the, nor can it be connected directly to an SCR or triac, because computer common is not normally referenced to one side of the ac supply.

Posets of annular non This technique extends the life of incandescent lamps and reduces EMI generated by load switching. Sensitive Gate Silicon Controlled Rectifiers. It has the same pin-out as More information.

Application Note AN-3003 Applications of Non Zero Crossing Triac Drivers Featuring the MOC3011

Remote Control of ac Voltage Local building codes frequently require all light ov wiring to be enclosed in conduit. The open-collector outputs require external pull-up More information.

RC15 Voltage-to-Frequency Converters www. A Survey of Zero-Knowl When the designer has more control of the input and output conditions, he can eliminate those components which are needed for his particular application to make the circuit more cost effective. Featuring very high commutation levels and high surge current capability.

This technique extends the life of incandescent lamps and mco3011 EMI generated by load switching. On the other hand, care should be taken to ensure that the maximum LED input current 50 ma is not exceeded or the lifetime of the may ov shortened.

Application Notes

Currents higher than 15 ma do not improve performance and may hasten the aging process inherent in LED’s. Of course, zero crossing can be generated within the micro-computer itself, but this requires considerable software overhead and usually just as much hardware to generate the zero-crossing timing thhe.

In order to design a snubber properly, one should really know the power factor of the reactive load, which is de? Since the triac turns off at zero current, it may be trying to turn off when the applied current is zero but the applied voltage is high.

Applications of Non Zero Crossing Triac Drivers_图文_百度文库

This is not quite enough to drive the MOC, nor can it be connected directly to an SCR or triac, because computer common is not normally referenced to one side of the ac supply. Assuming the forward drop to be 1.

By using a MOC, a triac, and a low voltage source, it is possible to control a large lighting load from a long distance through low voltage signal wiring which is completely isolated from the ac line.